The article below in relation to How to Install a Bathtub Yourself is pretty much enjoyable. Don't bypass it.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is readily available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a professional to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This article will assist you mount a new tub in your washroom if you have already bought a brand-new bathtub and don't need to change the plan of your previous water supply pipes.
Your tools and also material checklist need to comprise the following:
Preparing for the Installation
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted gain access to that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the level reads degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also check all joints and new pipework for leakages and also tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub should wait until the bathtub has been used at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, causing the water to permeate the wall between the bath and the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also conveniently readily available on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very eager about How to Install a Bathtub Yourself and I'm hoping you enjoyed reading the entire blog posting. Those who enjoyed our blog posting if you please do not forget to pass it around. Thanks a bunch for your time. Don't forget to stop by our website back soon.
Book Your Service